.webp&w=3840&q=75)
A Volkswagen may need welding because of body corrosion or damage to the underbody, sills, wheel arches, mounts and structural components. Volkkarihuolto Espoo carries out welding and body repairs at Ruukinmestarintie 7, 02330 Espoo.
The true extent of corrosion often becomes visible only after cleaning. We agree on the repair method and estimate before welding begins.
Welding is not needed only after a collision. Very often the cause is corrosion that develops gradually and is almost invisible at first.
Moisture, road salt, snow and temperature changes put the body under constant strain. Rust may develop beneath underbody protection, plastic trims and wheel-arch liners even when the vehicle looks clean outside.
01 — Welding
We repair structural and non-structural steel parts when welding is a safe and cost-effective solution.
Repair of outer and inner sills, reinforcements and damaged jacking points.
Local floor, seam and wheel-arch repairs followed by corrosion protection.
Welding of cracks, brackets and repairable exhaust pipe sections.
Restoration of metal mounts, guards and other repairable components.
Rust removal, welding, shape restoration and preparation for refinishing where required.
Repairs to sills, floors, jacking points and mounts before a vehicle inspection or re-inspection.
01
Sills are among the most vulnerable parts of a vehicle. They suffer from salt, moisture, dirt, stone impacts and incorrect lifting with a jack.
02
The underbody is constantly exposed to moisture, salt and dirt. Corrosion is especially serious when it affects structural parts, suspension mounts, brake pipes or powertrain mounting points.
03
Wheel arches are exposed to sand, stones, salt and dirt. Rust may begin as a small spot on an arch edge and spread beneath the paint.
04
Welding may be needed for internal mounts and metal components rather than visible body panels. Their condition can be especially important for vehicle safety.
05
The exhaust system is affected by salt, moisture and temperature changes. A local defect can sometimes be welded if the surrounding metal is still suitable for repair.
02 — Process
We assess the condition of the metal, the extent of corrosion and access to the damaged area. We determine whether a local repair is possible.
Severely corroded metal cannot simply be covered. It is removed so that the welded repair will be strong and safe.
A metal insert or suitable repair section is prepared to restore the original shape and strength.
After preparation, the repair section is welded in place to restore the strength and geometry of the damaged area.
The welds are cleaned and the surface is prepared for further treatment.
The metal is protected against renewed rust with primer, seam sealer or another material suitable for the repair area.
03 — Protection
Covering rust is not a repair. A lasting result requires sound metal, the correct joint and careful protection after welding.
Golf, Passat, Polo, Tiguan, Touran, Sharan, Caddy, Transporter, Multivan, Crafter, Touareg, T-Roc, T-Cross, Beetle, Jetta, Scirocco and other Volkswagen models.
In Finland, vehicle inspection may cover the condition of the underbody, sills, structural elements, mounts, brake pipes, exhaust system and other metal parts. If corrosion affects safety, the vehicle may fail katsastus. We can inspect your Volkswagen in advance and repair corrosion or damaged metal parts before inspection or re-inspection.
A small rust spot can quickly become a serious problem, especially when it is hidden or close to a structural element.
Yes. Volkkarihuolto Espoo carries out Volkswagen welding repairs at Ruukinmestarintie 7, 02330 Espoo.
Not always. If damage is too extensive or affects a structure that cannot be repaired safely, we recommend replacement or tell you honestly when repair is not sensible.
The price depends on corrosion extent, fabrication of the repair section and finishing. A reliable estimate can be provided after inspecting the car.
Yes. We repair corroded sills, floors and jacking points when the area can be restored safely.
Yes, when the damaged area can be restored safely. We first inspect how far corrosion has spread and whether a local repair is sensible.
Welding can be practical for local damage. If the metal is extensively weakened, replacement or a larger repair is usually the more durable choice.
Yes. The repaired metal and seams are protected with materials suited to the location.
Send a photo in advance or book an inspection at Ruukinmestarintie 7, 02330 Espoo.
Professional car service in Espoo. Book an appointment easily online or call us.
VAG owns one of the largest collections of automotive platforms in the world — many models from different brands are built on a common base (like MQB).
Professional service for all Volkswagen models
Examples of car service and repair work we have completed
The customer brought a 2019 Volkswagen Passat with a worn rear wheel bearing and an ABS sensor that needed replacement. The rear hub was removed, the old and new hub bearing units were compared side by side, and the ABS sensor mounting point was checked before installation. We performed the following procedures: - Removal of the rear wheel and brake components for access - Removal of the old hub bearing unit - Inspection and replacement of the ABS sensor - Installation of the new rear wheel bearing / hub - Reassembly of the brakes and wheel - ABS system function check After the repair, the rear wheel bearing runs smoothly, the ABS sensor works correctly, and the car is ready for safe driving without bearing hum or ABS faults.
Open case
The customer brought a 2006 Volkswagen New Beetle whose automatic transmission oil pan had been struck and dented. With the car on a lift, we confirmed the pan damage and found old, contaminated transmission fluid. The oil pan was removed, the magnet and used fluid were inspected, and the transmission filter was replaced. The dented pan was straightened, refitted with a proper seal, and the gearbox was filled with fresh oil. We performed the following procedures: - Inspection and removal of the transmission oil pan - Draining and assessing the old transmission oil - Checking the magnet and metal debris - Replacing the transmission oil filter - Straightening the oil pan - Refitting the pan and renewing the seals - Filling with new transmission oil and checking the level After the service, the oil pan is back in the correct shape, the oil and filter have been renewed, and the transmission is ready for safe use.
Open case
The customer brought a 2007 Audi S5 to our workshop for a car wash and protective coating. The silver S5 coupe was carefully cleaned in our wash bay with a pressure washer so the body, wheels and visible surfaces were ready before coating. We performed the following procedures: - Thorough exterior wash - Cleaning of wheels and wheel arches - Body preparation for protective coating - Application of protective coating to the paintwork After washing and coating, the car is clean, glossy and better protected against weather, dirt and road salt.
Open case
The customer brought a 2017 SEAT León 1.4 TSI to our workshop for scheduled maintenance. The car was raised on a lift so the engine oil and filter change, as well as an underbody inspection, could be carried out thoroughly. We performed the following procedures: - Draining the old engine oil - Replacing the oil filter - Refilling with fresh oil to manufacturer specification - Visual inspection of the chassis, suspension and possible leaks - Checking fluid levels - Reading fault codes and basic system diagnostics After the service, the car is ready for safe driving. Regular scheduled maintenance keeps the 1.4 TSI engine reliable and helps prevent more expensive repairs.
Open case.webp&w=3840&q=75)
The customer brought us a 2011 Audi S5 Cabriolet with a fault in the convertible roof system. A sensor in the roof system had failed, causing the roof to lift and get stuck in the wrong position, while the mechanism could no longer complete the opening or closing cycle correctly. This type of fault requires careful diagnostics, because several sensors, limit switches and control units work together in a convertible roof mechanism. We checked fault codes, roof position recognition and the movement of the mechanism so the roof could be safely released from the incorrect position without causing additional damage. We performed the following procedures: - Convertible roof system diagnostics with a tester - Faulty sensor location - Releasing the roof mechanism from the incorrect position - Sensor and wiring inspection - System testing through several opening and closing cycles After the repair, the convertible roof works correctly again: the roof opens and closes normally, and no active fault codes remained in the system. The vehicle was returned to the customer with a working and safely tested roof mechanism.
Open case.webp&w=3840&q=75)
The customer brought us a 2016 Volkswagen Passat 1.4 GTE Hybrid after symptoms pointing to an oil leak started to appear in the engine operation. During diagnostics, we found that the turbo shaft seal was damaged and the turbo had started leaking oil into the intake manifold. This kind of fault should be repaired in time, because oil entering the intake side can cause rough running, smoke, and in the worst case further engine damage. We removed the necessary components, inspected the intake system, and replaced the damaged turbo with a new unit. After the repair, we checked the system for leaks, verified oil tightness, and tested engine operation. The car was returned to the customer in good working condition, with the risk caused by the turbo oil leak eliminated.
Open caseHow Volkkarihuolto service works for Audi, Volkswagen, Skoda, Seat, and Cupra vehicles
Upon arrival, our specialist will receive your car, discuss the service needs, and perform an initial inspection.
We use original Audi diagnostic equipment and thoroughly check your vehicle to identify any potential issues.
If we find unexpected issues, we will contact you and propose a repair plan with a cost estimate before proceeding with the work.
Our professional team performs all necessary service work using original or OEM-approved parts.
An experienced technician checks all work performed and ensures your vehicle operates flawlessly.
We will notify you when your vehicle is ready for collection. We will explain all the work done and answer your questions.
