.webp&w=3840&q=75)
Škoda welding repairs may be needed because of corrosion in the sills, underbody, wheel arches, jacking points, mounts or body components. Volkkarihuolto Espoo carries out welding and body repairs at Ruukinmestarintie 7, 02330 Espoo.
The true extent of corrosion often becomes visible only after cleaning. We agree on the repair method and estimate before welding begins.
Welding is not needed only after a collision. Very often the cause is corrosion that develops gradually and is almost invisible at first.
Moisture, road salt, snow and temperature changes put the body under constant strain. Rust may develop beneath underbody protection, plastic trims and wheel-arch liners even when the vehicle looks clean outside.
01 — Welding
We repair structural and non-structural steel parts when welding is a safe and cost-effective solution.
Repair of outer and inner sills, reinforcements and damaged jacking points.
Local floor, seam and wheel-arch repairs followed by corrosion protection.
Welding of cracks, brackets and repairable exhaust pipe sections.
Restoration of metal mounts, guards and other repairable components.
Rust removal, welding, shape restoration and preparation for refinishing where required.
Repairs to sills, floors, jacking points and mounts before a vehicle inspection or re-inspection.
01
Sills are among the most vulnerable parts of a vehicle. They suffer from salt, moisture, dirt, stone impacts and incorrect lifting with a jack.
02
The underbody is constantly exposed to moisture, salt and dirt. Corrosion is especially serious when it affects structural parts, suspension mounts, brake pipes or powertrain mounting points.
03
Wheel arches are exposed to sand, stones, salt and dirt. Rust may begin as a small spot on an arch edge and spread beneath the paint.
04
Jacking points may be damaged by corrosion, incorrect lifting or a poor previous repair. Weak metal can make lifting the vehicle unsafe.
05
Welding may be needed for internal mounts and metal components rather than visible body panels. Their condition can be especially important for vehicle safety.
06
The exhaust system is affected by salt, moisture and temperature changes. A local defect can sometimes be welded if the surrounding metal is still suitable for repair.
02 — Process
We assess the metal, extent of corrosion and access to the damaged area.
Plastic trims, wheel-arch liners, underbody guards or obstructing parts are removed when necessary.
Severely corroded metal is removed so that the welded repair will be strong and safe.
A metal insert or repair section is prepared to restore shape and strength.
The strength, geometry and safety of the damaged area are restored.
The welds are cleaned and the surface prepared for further treatment.
The metal is protected with primer, seam sealer or another material suitable for the repair area.
03 — Protection
Covering rust is not a repair. A lasting result requires sound metal, the correct joint and careful protection after welding.
Škoda Fabia, Octavia, Superb, Rapid, Scala, Kamiq, Karoq, Kodiaq, Roomster, Yeti, Citigo and Enyaq. We work on Škoda vehicles of different generations, ages and mileages.
In Finland, vehicle inspection may cover the condition of the underbody, sills, structural elements, mounts, brake pipes, exhaust system and other metal parts. If corrosion affects safety, the vehicle may fail katsastus. We can inspect your Škoda in advance and repair corrosion or damaged metal parts before inspection or re-inspection.
A small rust spot can quickly become a serious problem, especially when it is hidden or close to a structural element.
Yes. Volkkarihuolto Espoo carries out Škoda welding repairs at Ruukinmestarintie 7, 02330 Espoo.
Not always. If damage is too extensive or affects a structure that cannot be repaired safely, we recommend replacement or tell you honestly when repair is not sensible.
The price depends on corrosion extent, fabrication of the repair section and finishing. A reliable estimate can be provided after inspecting the car.
Yes. We repair corroded sills, floors and jacking points when the area can be restored safely.
Yes, when the damaged area can be restored safely. We first inspect how far corrosion has spread and whether a local repair is sensible.
Welding can be practical for local damage. If the metal is extensively weakened, replacement or a larger repair is usually the more durable choice.
Yes. The repaired metal and seams are protected with materials suited to the location.
Sometimes. On some Škoda models, corrosion may be hidden beneath sill trims, wheel-arch liners or underbody guards.
Visit us at Ruukinmestarintie 7, 02330 Espoo. We repair Škoda sills, underbodies, arches, jacking points, mounts and other metal components and help prepare the vehicle for inspection.
Professional car service in Espoo. Book an appointment easily online or call us.
VAG owns one of the largest collections of automotive platforms in the world — many models from different brands are built on a common base (like MQB).
Professional service for all Škoda models
Examples of car service and repair work we have completed
.webp&w=3840&q=75)
The customer brought us a 2016 Volkswagen Passat 1.4 GTE Hybrid after symptoms pointing to an oil leak started to appear in the engine operation. During diagnostics, we found that the turbo shaft seal was damaged and the turbo had started leaking oil into the intake manifold. This kind of fault should be repaired in time, because oil entering the intake side can cause rough running, smoke, and in the worst case further engine damage. We removed the necessary components, inspected the intake system, and replaced the damaged turbo with a new unit. After the repair, we checked the system for leaks, verified oil tightness, and tested engine operation. The car was returned to the customer in good working condition, with the risk caused by the turbo oil leak eliminated.
Open case.webp&w=3840&q=75)
The customer brought an Audi S5 3.0TFSI to our workshop with a distinct metallic rattling noise from the front of the engine on cold start and at idle. Fault codes indicated camshaft position correlation errors — a classic symptom of a stretched timing chain and worn chain guides on the 3.0TFSI engines. Diagnostics revealed the following issues: - Stretched primary timing chain - Worn chain guides and tensioner - Camshaft position correlation fault codes - Metallic rattling noise from the front of the engine We performed a complete timing chain repair: - Disassembly of the front of the engine and accessories - Removal of old timing chain, guides and tensioner - Installation of new genuine parts (chain, guides, tensioner, sprockets) - Precise timing setup using special tools - Replacement of seals and engine oil - ECU basic settings and adaptation - Test drive and final fault code check After the repair, the engine starts cleanly, idle is smooth, and all abnormal noises have disappeared. The timely timing chain repair saved the customer from a significantly more expensive engine overhaul.
Open case
Diagnostic of a broken injector for a 2012 Audi Q7 3.0TDi V6. The customer came to our workshop with unusual engine behavior: engine jerking, power loss, and unusual noises. Our diagnostics revealed the following issues: - One injector was not working properly - Uneven engine operation - Power loss and increased fuel consumption - Possible error codes in the engine control unit We performed the following procedures: - Precise diagnostics using the engine control unit - Testing of injector operation - Fuel pressure measurement - Checking electrical signals of injectors - Fault determination and repair recommendations After diagnostics, the customer received a clear picture of the problem and repair recommendations. The broken injector requires replacement, which will restore the engine's original performance.
Open case
Comprehensive suspension repair for a 2009 Volkswagen Passat 1.4TSi CNG. The customer came to our workshop with uneven ride and unusual suspension noise issues. Diagnostics revealed several suspension problems: - Worn front suspension components (springs, shock absorbers, stabilizer bars) - Damaged rear suspension components - Steering wheel wear and unevenness - Brake system inspection and service We performed the following procedures: - Complete front suspension replacement - Rear suspension repair and parts replacement - Steering wheel balancing and adjustment - Brake system service - Suspension geometry adjustment - Test drive and testing After the repair, the car now rides smoothly, the suspension is softer, and handling has improved significantly. The CNG system continues to work flawlessly.
Open case
Complete replacement of DQ250 DSG clutch and flywheel on a 2014 Škoda Yeti 1.6 TDI. The customer came to our workshop when the clutch started slipping and unusual noises were heard from the transmission. Diagnostics showed complete wear of the clutch and flywheel. The DQ250 transmission is known for these issues, so the procedure was necessary. We performed the following work: - Transmission removal and disassembly - Inspection and removal of old clutch and flywheel - Installation of new dual clutch - Replacement of flywheel with new one - Transmission oil change - System adaptation and testing After the repair, the transmission works flawlessly, shifting is smooth, and all unusual noises have disappeared. The new clutch ensures long-term and reliable operation.
Open case
Repair of the DSG transmission on a 2022 Volkswagen Passat GTE, including replacement of all seals and solenoids. The customer came to the service with an issue of jerking when changing gears and delays in gear engagement. Diagnostics revealed a hydraulic problem in the DQ400 transmission caused by worn solenoids and leaking seals. We performed the following procedures: - Transmission fluid replacement and analysis - Transmission electronics diagnostics - Partial disassembly of the transmission - Replacement of all solenoids with new ones - Complete replacement of all seals - System adaptation and calibration After the repair, the transmission works like new, with precise and smooth gear changes.
Open caseHow Volkkarihuolto service works for Audi, Volkswagen, Skoda, Seat, and Cupra vehicles
Upon arrival, our specialist will receive your car, discuss the service needs, and perform an initial inspection.
We use original Audi diagnostic equipment and thoroughly check your vehicle to identify any potential issues.
If we find unexpected issues, we will contact you and propose a repair plan with a cost estimate before proceeding with the work.
Our professional team performs all necessary service work using original or OEM-approved parts.
An experienced technician checks all work performed and ensures your vehicle operates flawlessly.
We will notify you when your vehicle is ready for collection. We will explain all the work done and answer your questions.
